Parameters list
To get all available parameters of the device send command {"cmd":1}, for example answer for AX thermostat with firmware version 2.3:
{
"sn":"058016000543464839373520000159",
"par":[[0,6,"536112000"],[1,6,"536112000"],
[2,2,"1"],[3,2,"0"],[4,1,"30"],
[5,1,"30"],[6,1,"25"],[7,1,"5"],
[18,2,"2"],[19,2,"10"],[21,1,"0"],
[23,2,"6"],[25,2,"15"],[26,1,"45"],
[27,1,"5"],[28,2,"16"],[29,1,"0"],
[17,4,"175"],[114,7,"1"],[115,7,"0"],
[116,7,"0"],[117,7,"0"],[118,7,"0"],
[121,7,"0"],[122,7,"0"],[124,7,"0"],
[125,7,"0"]]
}
sn - device serial number
par - parameter exchange key
Transfer format is an array of arrays. The first value is number of the parameter, the second its type, the third is string with the parameter value.
For example, turn on the device and set floor temperature in manual mode to 27 °C (device menu item bLc = 0FF, blocking is disabled):
{
"sn":"058016000543464839373520000159",
"par":[[125,7,"0"],[5,1,"27"]]
}
Answer:
In firmware version 2.5, in response, we receive an updated list of parameters:
{
"sn":"058016000543464839373520000159",
"par":[[0,6,"536112000"],[1,6,"536112000"],[2,2,"1"],[3,2,"0"],[4,1,"30"],
[5,1,"27"],[6,1,"25"],[7,1,"5"],[18,2,"2"],[19,2,"10"],[21,1,"0"],
[23,2,"6"],[25,2,"15"],[26,1,"45"],[27,1,"5"],[28,2,"16"],[29,1,"0"],
[17,4,"175"],[114,7,"0"],[115,7,"0"],[116,7,"0"],[117,7,"0"],[118,7,"0"],
[121,7,"0"],[122,7,"0"],[124,7,"0"],[125,7,"0"]]
}
Важно
When changing device parameters, the command must contain the key sn
Num |
Type |
|---|---|
0 |
CStringType |
1 |
int8 |
2 |
uint8 |
3 |
int16 |
4 |
uint16 |
5 |
int32 |
6 |
uint32 |
7 |
bool |
Num |
Type |
Name |
Description |
|---|---|---|---|
0 |
6 (uint32) |
startAwayTime |
in seconds from 01.01.2000, away start time |
1 |
6 (uint32) |
endAwayTime |
in seconds from 01.01.2000, away end time |
2 |
2 (uint8) |
mode |
mode: schedule=0, manual=1 |
3 |
2 (uint8) |
controlType |
control tupe: by floor=0, by air=1, extended=2 |
4 |
1 (int8) |
manualAir |
in °C, manual mode temperature by air |
5 |
1 (int8) |
manualFloorTemperature |
in °C, manual mode temperature by floor |
6 |
1 (int8) |
awayAirTemperature |
in °C, temperature mode away by air |
7 |
1 (int8) |
awayFloorTemperature |
in °C, temperature mode away by floor |
14 |
2 (uint8) |
minTempAdvancedMode |
in °C, minimum floor temperature in extended mode |
15 |
2 (uint8) |
maxTempAdvancedMode |
in °C, maximum floor temperature in extended mode |
17 |
4 (uint16) |
power |
in a.e., P=(power<=150)?(power*10):(1500+power*20), connected power |
18 |
2 (uint8) |
sensorType |
type of connected temperature sensor: 4,7kOhm=0, 6,8kOhm=1, 10kOhm=2, 12kOhm=3, 15kOhm=4, 33kOhm=5, 47kOhm=6 |
19 |
2 (uint8) |
histeresis |
in 1/10 °C, hysteresis |
20 |
1 (int8) |
airCorrection |
in 1/10 °C, air temperature sensor correction |
21 |
1 (int8) |
floorCorrection |
in 1/10 °C, floor temperature sensor correction |
23 |
2 (uint8) |
brightness |
in a.e. (from 0 to 9) brightness |
25 |
2 (uint8) |
propKoef |
in minutes when load on within 30-minutes cycle of the proportional mode |
26 |
1 (int8) |
upperLimit |
in °C, max setting value of the floor temperature |
27 |
1 (int8) |
lowerLimit |
in °C, min setting value of the floor temperature |
28 |
2 (uint8) |
maxSchedulePeriod |
max number of perioods per day |
29 |
2 (uint8) |
tempTemperature |
in °C, temporary mode temperature |
31 |
2 (uint8) |
setTemperature |
in °C, setting temperature of current mode (awayFloorTemperature | manualFloorTemperature | tempTemperature) |
33 |
1 (int8) |
upperAirLimit |
in °C, max setting value of the air temperature |
34 |
1 (int8) |
lowerAirLimit |
in °C, min setting value of the air temperature |
52 |
4 (uint16) |
nightBrightStart |
in minutes from 00:00, night low bright start time |
53 |
4 (uint16) |
nightBrightEnd |
in minutes from 00:00, night low bright end time |
109 |
7 (bool) |
offButtonLock |
disable automatic lock of touch buttons (Read-only) |
114 |
7 (bool) |
androidBlock |
local newort control block |
115 |
7 (bool) |
cloudBlock |
cloud control block |
117 |
7 (bool) |
NCContactControl |
inverted relay |
118 |
7 (bool) |
coolingControlWay |
heat/cool mode |
120 |
7 (bool) |
useNightBright |
activate using night bright |
121 |
7 (bool) |
preControl |
preheat |
122 |
7 (bool) |
windowOpenControl |
open window control |
124 |
7 (bool) |
childrenLock |
children protect |
125 |
7 (bool) |
powerOff |
power off |